How to remove the air conditioning connecting pipe? How to disassemble the air conditioning connecting pipe?

The main products of our store are：Air Conditioner Parts(include Copper Tube,Ac Heat Exchanger,Air Conditioner Copper Pipe and so on),Refrigerator Parts,Clothes Dryer Parts.

With the development of technology and society, today's air conditioners are basically purchased by every household. But sometimes when you move a new house, you need to remove the air conditioner first when you need to shift the air conditioner. How to remove the air conditioner correctly? How to remove the Air Conditioning Connecting Pipe ? What is the method for disassembling the air conditioner? This edition of the home decoration network Xiaobian will introduce the method of disassembly and assembly of air conditioners, I hope to help everyone.

First, how to properly remove the air conditioner

1 recycling refrigerant

The refrigerant in the air conditioner must be collected into the outdoor unit. Before disassembling the machine, the air conditioner can be set up, and the cooling state can be set. After the compressor is running for 5-10 minutes, after the cooling state is normal, unscrew the cap on the interface between the liquid pipe and the gas pipe of the outer machine, and close the high pressure pipe (thin). The shut-off valve, after 1 minute, the tube surface condensation, immediately close the low-pressure pipe (coarse) cut-off valve, and at the same time quickly shut down, unplug the power plug, tighten the cap with a wrench, and the refrigerant recovery work is completed. You can also use the forced start button on the indoor unit to start up, and observe whether there are other faults in the indoor and outdoor units. Avoid troubles caused by air conditioning transfer.

2 remove the indoor unit

After the refrigerant is recovered, the indoor unit can be removed. Use a wrench to unscrew the indoor unit lock nut and use the prepared sealed sodium to protect the wire of the indoor unit connection joint to prevent the joint thread from being damaged during handling; then use the cross to remove the control line. At the same time, it should be marked to avoid mistakes during installation. If the signal cable or power cable is connected incorrectly, the external unit will not operate or the machine will not be controlled. The inner hanging plate is generally fixed relatively firmly, and it is difficult to unload it; after unloading, the hanging plate is removed, placed on a flat concrete floor, and then gently leveled and corrected.

3 disassembly of the outdoor unit

After unscrewing the outer machine to connect the lock nut, apply the prepared sealant to screw the wire to the outer joint. Then use a wrench to loosen the fixing screws on the outer foot. When disassembling and lowering the outdoor unit, it is best to use a rope to hang it. When disposing, pay attention to balance, avoid vibration, bump, and pay attention to safety. The outdoor air conditioning connecting pipe should be slowly straightened, and the four ports of the connecting pipe should be sealed with four plugs to prevent dust and moisture from entering the air. The plug is good, and finally it is tied with a plastic bag, which is easy to handle.

Second, how to remove the air conditioning connecting pipe

The disassembly of the air conditioning connecting pipe is actually a step in disassembling the air conditioner. The following small series specifically describes how to disassemble the air conditioning outer connecting pipe. When the air conditioner is in the cooling state, open the cover of the two connecting pipe valves of the outdoor unit with a wrench. Using a hex wrench, put it into a thin (high pressure valve) valve port and quickly close the valve. After about 20 seconds, turn off the thick valve (low pressure), then turn it off and turn off the power. This fluorine will receive the outside machine. Then you can remove the air conditioning connection tube.

Third, how to properly install air conditioning

After the air conditioner is removed, it will be installed.

1. When we install, we will set the hanging board of the indoor unit at the reserved position.

2. After the air-conditioning pipe is put on, the machine inside the room is hung.

3. Determine the seat of the outdoor unit according to the length of the air-conditioning pipe. We must also guarantee the level of the outdoor unit.

4. After connecting the high and low pressure air conditioning connecting pipes, we will open the high pressure valve, and then relax the lock nut of the low pressure pipe. The purpose of this is to eliminate the air in the pipe and hear the sound of the air 7~10. After that, tighten the lock nut, open the low pressure valve, and connect the wires in the order they are done.

5. Finally, turn on the power and check if the pipeline, wires, etc. are connected.

The above is the process of air-conditioning disassembly and assembly of the air-conditioning connecting pipe summarized by the decoration home network Xiaobian, I hope to help everyone in the future life, and can solve some small problems of air conditioning in the daily life. More knowledge about air conditioning can pay attention to our home appliances encyclopedia section to understand!